Good to see the workshop is up and running... still got to pop back down and see you about my car but just haven't had the time, soon for sure.
Printable View
Good to see the workshop is up and running... still got to pop back down and see you about my car but just haven't had the time, soon for sure.
Made a start on fitting up the Over-fenders.
http://i1082.photobucket.com/albums/...t/P1000171.jpg
Trimmed to an even size.
http://i1082.photobucket.com/albums/...t/P1000172.jpg
Test fitted.
http://i1082.photobucket.com/albums/...t/P1000176.jpg
http://i1082.photobucket.com/albums/...t/P1000177.jpg
Alignment done and Temporary Fixings in.
http://i1082.photobucket.com/albums/...t/P1000178.jpg
http://i1082.photobucket.com/albums/...t/P1000179.jpg
http://i1082.photobucket.com/albums/...t/P1000180.jpg
And a little more trimming.
http://i1082.photobucket.com/albums/...t/P1000186.jpg
http://i1082.photobucket.com/albums/...t/P1000187.jpg
The next step is going to be tackling the Offside panel damage before the Over-fenders can progress.
http://i1082.photobucket.com/albums/...t/P1000105.jpg
http://i1082.photobucket.com/albums/...t/P1000106.jpg
Looking good Will, but you have to crack on and make space for mine! I'm ready and waiting now, bushes are bought, loom is stripped, i'm ready! Let me throw some money at you! :)
Made a little progress with my Nascar spoiler.
http://i1082.photobucket.com/albums/...t/P1000169.jpg
http://i1082.photobucket.com/albums/...t/P1000170.jpg
http://i1082.photobucket.com/albums/...t/P1000174.jpg
http://i1082.photobucket.com/albums/...t/P1000175.jpg
Then made a start straightening the Rear Quarter panel.
Didn't want to go too mad as it will be covered, just straight enough to mount the Over-fender.
http://i1082.photobucket.com/albums/...t/P1000107.jpg
http://i1082.photobucket.com/albums/...t/P1000188.jpg
http://i1082.photobucket.com/albums/...t/P1000190.jpg
http://i1082.photobucket.com/albums/...t/P1000205.jpg
http://i1082.photobucket.com/albums/...t/P1000206.jpg
A few last adjustments.
http://i1082.photobucket.com/albums/...t/P1000207.jpg
http://i1082.photobucket.com/albums/...t/P1000208.jpg
Then got the Offside panel fitted.
http://i1082.photobucket.com/albums/...t/P1000209.jpg
http://i1082.photobucket.com/albums/...t/P1000210.jpg
will, i'm using an R33 front crossmember + CA/SR box + RB20 bell housing and needed to shorten the prop by 45mm, so I'm not sure you'll get away without doing the prop. it looks like you're mounting it closer to the firewall than I did too.
I've never had an RB20 gearbox rear half to compare to the CA/SR boxes though.
Thanks for the info Alan.
I'm using an S13 Cross-member + RB20 Box + Modified Motor and Box mounts.
It all seems to line up properly, Gearbox and Prop are fully engaged and the Gear selector sits quite central in it's hole.
I think the RB20 Box is a fair bit shorter than the RB25 Box, Unfortunately I didn't measure against the CA/SR Box when I had it.
Had a Bumper Delivery !
Unfortunately it's a Poor quality Fake Rocket Bunny.
I hate genuine Fail Bunny stuff, And thought this looks awful, So on the lookout for an Origin Rear now.
http://i1082.photobucket.com/albums/...t/P1000192.jpg
http://i1082.photobucket.com/albums/...t/P1000200.jpg
At least the Origin Side-skirts look good fitted up.
http://i1082.photobucket.com/albums/...t/P1000199.jpg
Progressed the Spoiler slightly.
http://i1082.photobucket.com/albums/...t/P1000211.jpg
http://i1082.photobucket.com/albums/...t/P1000212.jpg
Also made a start on the Wiring Loom.
http://i1082.photobucket.com/albums/...t/P1000161.jpg
Had a dry fit up of where it will need to run.
http://i1082.photobucket.com/albums/...t/P1000163.jpg
http://i1082.photobucket.com/albums/...t/P1000164.jpg
Looking good!
Looking very nice.
I have a question thou thats been bugging me since I followed Lam`s Aristo build. What are those fasteners You use for parts measuring etc??
Thanks a Lot
Thanks dude. :thumbs:
Those fasteners are 'Aviation Skin Pins' They were used primarily in the World War to temporarily fix the Aluminium Sheet to the Aircraft Fuselage before being Riveted.
They are basically a sprung loaded fixing that you insert through a pre-drilled 1/8th Inch hole.
Everywhere you see one on the Over-fenders, will have a Rivet in it's place when they're permanently fixed on. :D
Aka cleco pins I do believe. still used today!
Looks nice! Wasn't sure on rocket bunny style stuff but lve grown to it
Car looks awsome mate. But who the hell made those fenders they are shocking to need that much cutting off!
Thanks a lot Found those on uk ebay. Just need to get them to Poland now.
Keep up the good work, I remember my jaw dropped when I saw Lam`s car on clubaristo so I`m sure this will be amazing as well..
The Loom was a bit of a mess.
Looks like someone had started to try a conversion, but only had a crack at odd bits, and some was quite messy.
http://i1082.photobucket.com/albums/...t/P1000117.jpg
http://i1082.photobucket.com/albums/...t/P1000118.jpg
http://i1082.photobucket.com/albums/...t/P1000120.jpg
Decided to strip it all back and begin converting from SR to RB, I'll also remove anything I don't want to thin it out.
Where someone had already cut the slam panel for access, I started to tidy it up, and strengthen it up with some mounting points.
http://i1082.photobucket.com/albums/...t/P1000202.jpg
Hammered out a couple of Brackets.
http://i1082.photobucket.com/albums/...t/P1000203.jpg
http://i1082.photobucket.com/albums/...t/P1000204.jpg
Temporarily mounted them up.
http://i1082.photobucket.com/albums/...t/P1000217.jpg
Welded some Nuts to the bottom to make a captive fixing.
http://i1082.photobucket.com/albums/...t/P1000218.jpg
Welded the Brackets onto the chassis side.
http://i1082.photobucket.com/albums/...t/P1000220.jpg
And test fitted the now Bolt-on Panel.
http://i1082.photobucket.com/albums/...t/P1000221.jpg
http://i1082.photobucket.com/albums/...t/P1000222.jpg