Search:

Type: Posts; User: JCD

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    1
    Views
    240

    S14 seat belt in S13?

    Guys,
    Will the stock S14 front seat belts fit in a S13?
    Cheers,
    JCD
  2. Replies
    10
    Views
    1,537

    I think I can understand about the restriction...

    I think I can understand about the restriction but why is the high water speed through the thermo housing?
  3. Replies
    12
    Views
    892

    You shouldn't have oil pooling in the drain...

    You shouldn't have oil pooling in the drain neither.
  4. Thread: CA Intake Brackets

    by JCD
    Replies
    6
    Views
    299

    These brackets are not just there for fun. The...

    These brackets are not just there for fun.
    The cornflakes-box-style gaskets at the inlet can start to leak when you take them away, which is a nasty fault to trace and even more nasty to repair....
  5. Thread: The Wasp

    by JCD
    Replies
    56
    Views
    25,992

    End of July I went to the Superflow rolling road....

    End of July I went to the Superflow rolling road.
    The result is in line with what I expected - 279hp and 313Nm, reaching 200Nm just over the 1800rpm, so less power but more torque than the...
  6. Replies
    0
    Views
    174

    Cvfhvl 11036-d4200 :)

    aka Check valve for hydraulic valve lifter (11036-D4200).
    This item has been unavailable for a long while AFAIK.
    I was able to order two pieces of these from Humphris Oxford in the UK via their...
  7. Thread: The Wasp

    by JCD
    Replies
    56
    Views
    25,992

    The noise :) ...

    The noise :)


    http://s584.photobucket.com/user/Four_stroke_guerrilla/media/S13/P4140005_agk_zps73d4e8c8.mp4.html
  8. Thread: The Wasp

    by JCD
    Replies
    56
    Views
    25,992

    The throttle body is doing fine as well as the...

    The throttle body is doing fine as well as the idle switch workaround.
    I moved the air filter from the left to right side of the engine bay.
    It's placed now where the battery used to be.
    Some...
  9. Replies
    39
    Views
    2,563

    This is good info, thanks.

    This is good info, thanks.
  10. Replies
    39
    Views
    2,563

    Was that with the restrictor in?

    Was that with the restrictor in?
  11. I can't see why this would be different for Tomei...

    I can't see why this would be different for Tomei pistons.
    It might be different for a different material of piston rings but as we are all using the same cast iron engine blocks I really can't see...
  12. Thread: The Wasp

    by JCD
    Replies
    56
    Views
    25,992

    It was not possible to find a 4-in-1 header that...

    It was not possible to find a 4-in-1 header that fits the CA18 with left hand drive.
    All JDM stuff will fit RHD but no guarantee for LHD.
    I didn't want to pay for shipment and import duty and get...
  13. Replies
    12
    Views
    732

    :D:thumbs: Yes, good question. I haven't...

    :D:thumbs:


    Yes, good question.
    I haven't seen a single broken TPS sensor yet.
    How did you diagnose the sensor?
    Is it the potmeter part or the idle switch part that is bad?
  14. Replies
    12
    Views
    732

    Yep. It has a bit inside that you don't need...

    Yep.
    It has a bit inside that you don't need -the full throttle switch- but it's not wired in your engine harness so it won't do no harm.
  15. Replies
    12
    Views
    732

    You can use the TPS from an automatic straight...

    You can use the TPS from an automatic straight away without any modification.
    It might be a bit more expensive that's all.
  16. Replies
    12
    Views
    732

    Is there an immobiliser ?

    Is there an immobiliser ?
  17. HITACHI application lists and part number cross references

    Very little about our cars but still interesting.
    Best is to save the pdf's; you never know how long such info will be available.
    ...
  18. The o-ring for the fuel pump cover has the Nissan...

    The o-ring for the fuel pump cover has the Nissan partnumber 17342-01A00.
    I replaced mine with an industrial item in Viton (which is better than nitrile rubber) 120mm diameter, 4mm thick.

    Link to...
  19. In the past I've seen that kind of problems...

    In the past I've seen that kind of problems solved with injectot cleaner. But it was not on S13 and it seems to me that in your case the problem is worse than it was there.
    How many miles has the...
  20. Is that while driving or while revving in...

    Is that while driving or while revving in neutral?



    As mentioned in the previous posts, check for bost leaks and ditch the hot start solenoid.
  21. Replies
    9
    Views
    911

    You have PM :)

    You have PM :)
  22. Replies
    9
    Views
    911

    :no::ghey::p :)

    :no::ghey::p :)
  23. Replies
    9
    Views
    911

    Thanks Can you send me a picture? Just...

    Thanks


    Can you send me a picture?

    Just making sure all is clear: it should fit on a CA18DET engine, in a S13 Rear wheel drive, Left hand steering.
  24. Replies
    9
    Views
    911

    NA tubular manifold

    The CA18DET engine came with a turbo but I replaced it by a supercharger.
    Currently I'm using the stock cast iron manifold and a 10 years old Mongoose exhaust line.
    The hot side of the turbo was...
  25. Thread: The Wasp

    by JCD
    Replies
    56
    Views
    25,992

    I installed one of these 70mm shiny ebay...

    I installed one of these 70mm shiny ebay "universal throttle bodies".
    Compared to the stock item it is very bulky and it was dropped-in somewhat temporarily so I won't post a picture of it right...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4