Such a sick car man, only thing that lets it down is the rear arches :(
Type: Posts; User: eurospec
Such a sick car man, only thing that lets it down is the rear arches :(
This is the only picture I have that kinda shows the fitment at the moment. I am running a 15mm spacer and S14 lower arms too so will push the wheel out a further too. I needed a spacer on the front...
Good luck then. I run 17x9.75 on a PS13 with 225/45 rear and 235/40 up front, no rear camber, -6 front camber.
You can fit any of the sizes they do on an S13. Don't need much arch work on the rear to get clearance on a 17x9.75 ET25, depends how low you go.
Shall be there in the Soarer. Just about to leave for the loooonnnggg journey up there!
...
Black Soarer, spent all day on the 100 circuit
I have the same thing with my ACT clutch, and so does a friend who fitted a Comp clutch.
I think it is either the slave cylinder or the clutch pivot ball. I'm going to take my gearbox off in a...
Yeh the make of the filter I use is RamAir, not 'ram-air' like motorbikes etc use haha.
Id rather use a foam filter than a gauze/cotton one, flow better when the filter is a little dirty.
Yeh why?
Yes
Yep fit straight onto S14 ends. S13's are different as they use a smaller diameter tie-rod.
Fitted this setup to 4 seperate cars with no issues.
RamAir
This is how I do mine
https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-prn2/t1.0-9/968848_10151579652580816_978843602_n.jpg
You need to relocate the loom where it goes inside the car.
It will still rub even above the arch if your car is properly low/has increased steering lock. I drilled a new hole in the bulkhead but...
I have one of these in my garage if anyone wants to buy it off me, I don't use it anymore
Desmond Regamasters. Come with the added benefit of looking awesome too.
It clicks fine, if I bridge the 2 wires sometimes it will stop the rattling, othertimes it won't. I'll just replace the switch and see what happens. The VVT is alot worse than it was before though,...
I think that the Godspeed arbs are wrong personally. If you set the car up with it on level ground there should be little pre-tension on the ARB, there is loads on the Godspeed ones, and it doesn't...
I would stick with standard ARB's and run a slightly stiffer spring. Does the car have coilovers already? If not go for CS2's!
I would also not worry about diff bushes, but put solid subframe bushes...
Just an update on mine.
The switch worked fine for a very long time, then about a month ago it started rattling again. Getting really really bad now, going to try changing the switch for a new...
What are your inlet to turbo pipes like? Are they also coated in oil? My turbo was the same, turned out engine was blowing a fair bit of oil into the breather before the turbo and made it look the...
Will be Aiden, not sure if he's a member on here or not.
Thats why you get genuine so they don't get so badly damaged, ABS is able to withstand alot more abuse than fibreglass. I ran over my kouki front bumper at 40mph and it's still in one piece, albeit...
Yeh, I run Navan/Zenki skirts with Kouki bumpers, didn't mean the standard Kouki skirts.
Id spend the money for a vertex kit on some genuine Navan skirts, Kouki rear bumper and Kouki spats.
Depends on ride height. If you're willing to run it ridiculously low then you can pull it off.
Struggles old S14 on 17's with a vertex kit.
...