Search:

Type: Posts; User: norfy

Page 1 of 18 1 2 3 4

Search: Search took 0.05 seconds; generated 15 minute(s) ago.

  1. Replies
    30
    Views
    5,467

    Speak to Keeve Alan McIver on fb, he's making...

    Speak to Keeve Alan McIver on fb, he's making these with/without the bypass for very cheap at the moment
  2. Replies
    3
    Views
    884

    You can use the UK S13 wiring diagrams for that...

    You can use the UK S13 wiring diagrams for that circuit as they are the same chassis side.

    You say you heard a clicking under the bonnet, have you thought about replacing the ECCS relay? It could...
  3. Replies
    6
    Views
    642

    Its a big job, a little easier on a stripped...

    Its a big job, a little easier on a stripped track car with no heaters.

    The main issues are;
    - routing the bulk of the cables (because there are a lot of interior components that get in the way,...
  4. Sumitomo don't make the connectors anymore but...

    Sumitomo don't make the connectors anymore but there are companies out there (mainly alibaba but in bulk) that do produce copies.

    Finjector are the only place (apart from alibaba) i've found that...
  5. Apparently Audi TT coils are the ones to go for,...

    Apparently Audi TT coils are the ones to go for, exactly the same coil just a little shorter so you can get the coil pack cover on afterwards. i've also seen people cut the rubber (boot?) on the TT...
  6. Replies
    13
    Views
    6,836

    if you struggle with the little screws i find a...

    if you struggle with the little screws i find a small pair of long nose vice grips can do well to help
  7. Replies
    5
    Views
    1,901

    It sounds very much like you've got the S13...

    It sounds very much like you've got the S13 silvia cluster and HUD (although some/few 180sx had them fitted)

    The HUD will read 0 at all times until it senses a speed signal from the gearbox...
  8. Replies
    6
    Views
    692

    browns are ignition lives, blacks are earths on...

    browns are ignition lives, blacks are earths on nissan circuits.

    if you put an earthed piece of wire up that yellow/purple wire the dash light should come on with ignition. if it doesnt then...
  9. Replies
    2
    Views
    358

    http://latinopoetryreview.com/wp-content/uploads/2...

    http://latinopoetryreview.com/wp-content/uploads/2018/04/new-mass-air-flow-sensor-wiring-diagram-inspirational-how-to-turbo-a-ka24de-with-a-250-300whp-goal-zilvia-forums-ideas-of-mass-air-flow-sensor-...
  10. i would swap the fuel pump and make notes of the...

    i would swap the fuel pump and make notes of the voltage and current on both, then test the voltage coming down the feed wire to the pump with the ignition on to see what voltage is being delivered....
  11. Replies
    3
    Views
    367

    itll be grabbing on the spigot bearing. Worth...

    itll be grabbing on the spigot bearing. Worth checking that it hasnt had a pull type clutch fitted as well, could need that releasing first.
  12. Replies
    7
    Views
    473

    to confirm, you have the correct wire for the...

    to confirm, you have the correct wire for the tacho from the nissan side.

    is it a straightcam sr20? just thinking the earlier s13 engines/tacho sr/ca use a negative pulse tacho signal...
  13. Replies
    23
    Views
    1,585

    think i have a converted series 1 loom in the...

    think i have a converted series 1 loom in the garage if that helps
  14. Replies
    10
    Views
    850

    sounds too cheap to me, arent they like £250 in...

    sounds too cheap to me, arent they like £250 in japan? plus it concerns me theyve listed that the injectors have been flow tested, if they were genuine new in the box then surely you wouldnt flow...
  15. you will damage the ecu if you put power down the...

    you will damage the ecu if you put power down the black/pink stripe wire on the back of the relay.

    you need the ecu and cas connected for the pump to prime as well.
  16. when you did the sr20det conversion did you move...

    when you did the sr20det conversion did you move the brown wire on the brown f8 connector to match up with the chassis loom?

    low voltage to the injectors will be either a relay breaking down (coil...
  17. Replies
    3
    Views
    317

    also need to consider the retractor angle if yore...

    also need to consider the retractor angle if yore going to use ones from another car
  18. Replies
    18
    Views
    983

    rust is a like a disease, you really need to chop...

    rust is a like a disease, you really need to chop it out and treat the areas that have been affected. i feel that youll never fully remove rust with all the tight seams and multi layer panels its...
  19. afraid i dont seem to have any pictures. It was...

    afraid i dont seem to have any pictures. It was quite simple, i used a 'L' shaped bar roughly 5-6 inches long, one end was drilled and fixed onto the exhaust housing using one of the original core...
  20. +1 for bracing the turbo. I made up a small...

    +1 for bracing the turbo. I made up a small bracket to help take the weight of the turbo as well and havent had an issue in 5 years with a japspeed manifold (they used to be common for cracking). i...
  21. Apologies, kept forgetting :/ Anyway. On my...

    Apologies, kept forgetting :/

    Anyway. On my car at 18*c I'm getting 2.456 kOhm
  22. Ill pull one out of one of my cars and have a...

    Ill pull one out of one of my cars and have a measure
  23. Replies
    33
    Views
    8,445

    thanks :) ive made MANY mistakes to get to a semi...

    thanks :) ive made MANY mistakes to get to a semi decent finish. I prefer paint tbh, get a better finish, but its just the faff of prep and cleaning with the spray gun.
  24. youd need a sensor from a 180 or ps13, i believe...

    youd need a sensor from a 180 or ps13, i believe there are some uk ones also. gotta be someone breaking one
  25. thats the sensor, or at least the cables. there...

    thats the sensor, or at least the cables. there should also be a 10mm id plastic hose in there although this isnt as important as the sensor itself.
Results 1 to 25 of 440
Page 1 of 18 1 2 3 4