Search:

Type: Posts; User: stacky

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Passed. Old lambda was 100% dead (86k...

    Passed.

    Old lambda was 100% dead (86k original Nissan sensor)....

    New lambda figure was bang on 1 (should be between 0.97 and 1.03).

    My co went from 6.5% to 0.07%!!!!!!!!

    Really am...
  2. Thanks for all the replies lads.... So just...

    Thanks for all the replies lads....

    So just another update: I tested the signal wire output on the sensor last night and got a constant 0.25/0.28 volts.
    That was with the harness plagged into...
  3. Also, can anyone give me a simple test to check...

    Also, can anyone give me a simple test to check that the lambda sensor is working / grounded?

    Not fully sure which wire should have continuity with the chassis.
  4. I was assuming that mine would be the same as...

    I was assuming that mine would be the same as that.....

    I searched SXOC after it failed and saw a thread about earthing the exhaust for the lambda sensor.... So that's why my sensor isnt working....
  5. Not the answer i was looking for lol! I'm in...

    Not the answer i was looking for lol!

    I'm in ROI lads, its and NCT, not an MOT - we get it done in a test centre over here, not down the local garage!
  6. Thanks. Couple more questions if people could...

    Thanks.

    Couple more questions if people could give some advice from experience:

    1). Does the pre cat (on the standard downpipe) make much of a differance? I ask because i'm thinking about...
  7. Is there a flow direction on s14 cats? (Emissions failure)

    Refitted my cat for the test.... Failed on co and lambda.

    Found that there was no continuity on the lambda earth - so that's one thing sorted!
    However.... The co was 6.5 at Hugh idle (limit is...
  8. Replies
    8
    Views
    432

    Turbo gasket surely? The whistle being the gas...

    Turbo gasket surely?

    The whistle being the gas escaping and the ***t boost because the turbo isn't getting linear exhaust flow into the compressor due to the leak...
  9. Replies
    1
    Views
    310

    standard length of S14 wheel studs?

    What’s the standard length of S14 wheel studs?

    I’m after a set of extended ones, but I have some very pretty closed end wheel nuts that I have become emotionally attached to…. So I don’t want to...
  10. Thread: tyre pressure?

    by stacky
    Replies
    7
    Views
    372

    i'm running 35 up front and 45 on the rear

    i'm running 35 up front and 45 on the rear
  11. S14 lost remote fob.... what are my options?

    Car never came with a spare and i now have none.....

    Is this a bend over for the main dealer job, or is there another way around it (ie buy a fob from another 14 and reprogram it)?

    Car is an...
  12. The guy that owned it told me that he reversed...

    The guy that owned it told me that he reversed the exhaust into a kerb a few weeks before i bought it (i thought nothing of it)...... anyways, it turns out that the turbo gasket was fine.... the...
  13. Replies
    0
    Views
    457

    Pic request - Red 14A with front tow strap

    Just wanting to get an idea of what colour combo / location to go with.

    Mounting is not a problem, just purely a visual request.

    Thanks you please!
  14. Decided to stick on a FMIC at the weekend..... I...

    Decided to stick on a FMIC at the weekend..... I noticed that the old WMIC had expanded by about 2-3mm on one side..... looked like the retainingclasps had relaxed (if youve seen one up close you'l...
  15. It does have a walbro 255.... but regardless if...

    It does have a walbro 255.... but regardless if it had a 255l or a 300l pump, the fpr is what controls the fuel allowed into the injector rail.
    so in my mind the walbro will make no difference.
    ...
  16. I woulda said that myself only for the fact that:...

    I woulda said that myself only for the fact that:
    1). The boost holds perfectly all the wsy through tge rev range... no creep
    2) the boost comes on VERY quickly at about 2600 rpm
  17. Advice please – S14 ran too rich on dyno – stage 1 mods

    Hi all,

    Looking for some advice…..

    Rolling roaded my car yesterday and was happy with the power but concerned about the air/fuel ratio.
    First off, my mods are:
    Air filter.
    Decat and cat...
  18. Replies
    6
    Views
    261

    Cheers for the reply lads. I considered...

    Cheers for the reply lads.

    I considered welding..... but this 14 is a "keep it original" kinda car, not too keen on welding although the thought had already crossed my mind.

    I'm not burning up...
  19. Replies
    6
    Views
    261

    Copper Cometic turbo gaskets - any good?

    Well..... its that time again where i have to replace yet another turbo gasket!

    I have tried a lot of types over the last few years....
    Original Nissan - OK but still fails after a while.
    Fiber...
  20. Replies
    2
    Views
    320

    that is such a better feed than the formulad...

    that is such a better feed than the formulad site!!!!
  21. Replies
    1
    Views
    520

    S14 ABS vs Non ABS diff compatability

    Hi guys,

    I know that the non abs diffs (from JDM models) have a shorter nose and longer prop compared to the UK S14's.

    My question is, has anyone ever made up a spacer to fit a non abs jdm diff...
  22. That's the one! Cheers mate. Think that will be...

    That's the one! Cheers mate. Think that will be on the to do list for next weekend!
  23. Any pics fitted lads?

    Any pics fitted lads?
  24. Pic request - Red S14A with the grille sprayed black

    My grill is faded.... instead of spending a bizillion pounds on a plastic Kouki jdm grill..... i'm thinking about just spraying mine black.


    Anyone done this? If so, any pics?
  25. Replies
    8
    Views
    1,664

    Bloody hell thats a great result. Fair play man!

    Bloody hell thats a great result. Fair play man!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4