Search:

Type: Posts; User: Adzsy

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    2,951

    It sounds like your wastegate is opening on the...

    It sounds like your wastegate is opening on the turbo. To suddenly lose 1.5bar, and it not sound like a dump valve venting, it has to be more than just a loose pipework clip.
    Have you tried...
  2. Replies
    1
    Views
    253

    Ok. Just in case anyone else is searching. The...

    Ok. Just in case anyone else is searching. The replacement that arrived today reads 0.346 M Ohms and 5.1v.

    The one on my car when set to 0.346 M Ohms reads 3v.

    I'll update when I swap them...
  3. Replies
    1
    Views
    253

    HELP - Voltage check on AFM 4th wire

    Can anyone tell me roughly what the 4th wire on the pre face lift afm should have as a voltage.

    It doesn't say in the manual, and it goes to pin 37 on the ecu.

    I know it is a potentiometer to...
  4. Replies
    3
    Views
    4,062

    Fitted new FPR, its 90% better, but there is...

    Fitted new FPR, its 90% better, but there is still a light fluctuation. I would expect a rock steady reading at idle.
  5. Replies
    3
    Views
    4,062

    The fuel pump is an external Walbro bought new,...

    The fuel pump is an external Walbro bought new, although doesn't mean its not knackered, but seems to pump really well. I have a Voltage at pump of 13.4V when running.

    I am hoping it is the...
  6. Replies
    3
    Views
    4,062

    Erratic/Fluctuating Fuel Pressure CA18DET

    So I am hoping this video link below works. Here is my issue.

    I have a CA18DET fitted in my old RA23 Celica.

    Just as my car comes on boost (around 4-4.5K RPM) it goes flat, at 5K it takes off....
  7. Hesitation No power lots of noise befire 4.5k RPM

    Just thought I'd post this for future reference.

    I have been struggling with lack of power, hesitation and generally running like crap below approx. 4.5K RPM.

    Spec;

    CA18DET in an RA23 Celica...
  8. Replies
    8
    Views
    918

    Well turns out it was indeed that gasket from the...

    Well turns out it was indeed that gasket from the cover plate. The people that rebuild it didn't replace it. Makes me wonder else they cut corners on!
  9. Replies
    8
    Views
    918

    Gearbox off then.........again!

    Gearbox off then.........again!
  10. Replies
    8
    Views
    918

    It is definitely gearbox oil coming out. I did...

    It is definitely gearbox oil coming out. I did actually change the rear crank seal, but the box has been off for weeks and shortly after filling it, out it came again!

    I can't believe this ****!ng...
  11. Replies
    8
    Views
    918

    CA18 Gearbox oil leak

    So, I had my gearbox rebuild by a local company who basically just changed all the shaft bearings, seals etc.

    After a painstaking day, I filled it with oil, and it is dripping out between the bell...
  12. Replies
    0
    Views
    11,404

    CA18DET Alloy Radiator 42mm

    Any traders got a 42mm alloy radiator in stock. S13 CA18DET
  13. Replies
    100
    Views
    29,825

    Hi Mate, I use the R33 GTST Spec 2 ECU. The...

    Hi Mate, I use the R33 GTST Spec 2 ECU.

    The loom you have is a good start, but does differ a little on the F2 loom. Give me a shout when you get round to doing it. Mine will be different to yours...
  14. Replies
    16
    Views
    2,458

    Nice rides. Love the S15! Welcome. And this...

    Nice rides. Love the S15! Welcome.

    And this Z33 gearbox sounds fun, anyone know if it will go on an RB?
  15. Replies
    8
    Views
    494

    I have a new delphi ECU coolant temp sensor if...

    I have a new delphi ECU coolant temp sensor if you need one. This does sound very much like a faulty temp sensor. PM me if your interested.
  16. Replies
    100
    Views
    29,825

    Hi buddy and thanks... I think the Spec S...

    Hi buddy and thanks...

    I think the Spec S manual follows the same pinout as the Spec R, but with less pins as it won't have boost solenoid etc. When I did mine I followed the guides for the RB25...
  17. Replies
    7
    Views
    898

    did you ever sort this?

    did you ever sort this?
  18. Replies
    8
    Views
    632

    The other alternative is RHD japan.

    The other alternative is RHD japan.
  19. Replies
    8
    Views
    632

    assuming you have tried Nissan?

    assuming you have tried Nissan?
  20. Replies
    8
    Views
    929

    Spec S has a smaller diameter prop than S14 and...

    Spec S has a smaller diameter prop than S14 and Spec R.
  21. Replies
    15
    Views
    2,158

    If the lambda was screwed you would expect it to...

    If the lambda was screwed you would expect it to run smoother unplugged.

    I often unplug when I suspect it to be faulty and it drives nearly as well without than with....a little richer but that's...
  22. Replies
    2
    Views
    1,786

    I always spray the new coiled wire with pledge....

    I always spray the new coiled wire with pledge. Keeps the feed nice and smooth.
  23. Replies
    24
    Views
    3,844

    Agreed! I have been battling with my CA...

    Agreed! I have been battling with my CA conversion because I have basically had to buy everything for a tall block. When you have 10 second hand components from 10 different cars you just don't know...
  24. Solved! Simple, I connected the resistor...

    Solved! Simple, I connected the resistor connection to the transistor and vice versa upon reassembly!
  25. Ignition will not turn off / Weak spark / Non starter....?????

    This project has challenged me like no other, so here is my latest problem that I just cannot resolve.

    For back ground I have put a CA18DET in my RA23 celica. All wiring of the F8 and F10...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4