Search:

Type: Posts; User: eurospec

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    166
    Views
    58,128

    Such a sick car man, only thing that lets it down...

    Such a sick car man, only thing that lets it down is the rear arches :(
  2. This is the only picture I have that kinda shows...

    This is the only picture I have that kinda shows the fitment at the moment. I am running a 15mm spacer and S14 lower arms too so will push the wheel out a further too. I needed a spacer on the front...
  3. Good luck then. I run 17x9.75 on a PS13 with...

    Good luck then. I run 17x9.75 on a PS13 with 225/45 rear and 235/40 up front, no rear camber, -6 front camber.
  4. You can fit any of the sizes they do on an S13....

    You can fit any of the sizes they do on an S13. Don't need much arch work on the rear to get clearance on a 17x9.75 ET25, depends how low you go.
  5. Replies
    37
    Views
    3,012

    Shall be there in the Soarer. Just about to leave...

    Shall be there in the Soarer. Just about to leave for the loooonnnggg journey up there!
    ...
  6. Replies
    30
    Views
    5,133

    Black Soarer, spent all day on the 100 circuit

    Black Soarer, spent all day on the 100 circuit
  7. Replies
    2
    Views
    196

    I have the same thing with my ACT clutch, and so...

    I have the same thing with my ACT clutch, and so does a friend who fitted a Comp clutch.

    I think it is either the slave cylinder or the clutch pivot ball. I'm going to take my gearbox off in a...
  8. Replies
    27
    Views
    1,495

    Yeh the make of the filter I use is RamAir, not...

    Yeh the make of the filter I use is RamAir, not 'ram-air' like motorbikes etc use haha.

    Id rather use a foam filter than a gauze/cotton one, flow better when the filter is a little dirty.
  9. Replies
    27
    Views
    1,495

    Yeh why?

    Yeh why?
  10. Replies
    3
    Views
    407

    Yes

    Yes
  11. Replies
    5
    Views
    223

    Yep fit straight onto S14 ends. S13's are...

    Yep fit straight onto S14 ends. S13's are different as they use a smaller diameter tie-rod.

    Fitted this setup to 4 seperate cars with no issues.
  12. Replies
    27
    Views
    1,495

    RamAir

    RamAir
  13. Thread: Arch loom mod

    by eurospec
    Replies
    37
    Views
    2,832

    This is how I do mine ...

    This is how I do mine

    https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-prn2/t1.0-9/968848_10151579652580816_978843602_n.jpg
  14. Thread: Arch loom mod

    by eurospec
    Replies
    37
    Views
    2,832

    You need to relocate the loom where it goes...

    You need to relocate the loom where it goes inside the car.
    It will still rub even above the arch if your car is properly low/has increased steering lock. I drilled a new hole in the bulkhead but...
  15. Thread: Gauges

    by eurospec
    Replies
    30
    Views
    1,714

    I have one of these in my garage if anyone wants...

    I have one of these in my garage if anyone wants to buy it off me, I don't use it anymore
  16. Desmond Regamasters. Come with the added benefit...

    Desmond Regamasters. Come with the added benefit of looking awesome too.
  17. Replies
    113
    Views
    16,193

    It clicks fine, if I bridge the 2 wires sometimes...

    It clicks fine, if I bridge the 2 wires sometimes it will stop the rattling, othertimes it won't. I'll just replace the switch and see what happens. The VVT is alot worse than it was before though,...
  18. Replies
    49
    Views
    3,000

    I think that the Godspeed arbs are wrong...

    I think that the Godspeed arbs are wrong personally. If you set the car up with it on level ground there should be little pre-tension on the ARB, there is loads on the Godspeed ones, and it doesn't...
  19. Replies
    49
    Views
    3,000

    I would stick with standard ARB's and run a...

    I would stick with standard ARB's and run a slightly stiffer spring. Does the car have coilovers already? If not go for CS2's!
    I would also not worry about diff bushes, but put solid subframe bushes...
  20. Replies
    113
    Views
    16,193

    Just an update on mine. The switch worked...

    Just an update on mine.

    The switch worked fine for a very long time, then about a month ago it started rattling again. Getting really really bad now, going to try changing the switch for a new...
  21. Replies
    10
    Views
    702

    What are your inlet to turbo pipes like? Are they...

    What are your inlet to turbo pipes like? Are they also coated in oil? My turbo was the same, turned out engine was blowing a fair bit of oil into the breather before the turbo and made it look the...
  22. Replies
    3
    Views
    407

    Will be Aiden, not sure if he's a member on here...

    Will be Aiden, not sure if he's a member on here or not.
  23. Replies
    5
    Views
    280

    Thats why you get genuine so they don't get so...

    Thats why you get genuine so they don't get so badly damaged, ABS is able to withstand alot more abuse than fibreglass. I ran over my kouki front bumper at 40mph and it's still in one piece, albeit...
  24. Replies
    5
    Views
    280

    Yeh, I run Navan/Zenki skirts with Kouki bumpers,...

    Yeh, I run Navan/Zenki skirts with Kouki bumpers, didn't mean the standard Kouki skirts.

    Id spend the money for a vertex kit on some genuine Navan skirts, Kouki rear bumper and Kouki spats.
  25. Replies
    5
    Views
    280

    Depends on ride height. If you're willing to run...

    Depends on ride height. If you're willing to run it ridiculously low then you can pull it off.
    Struggles old S14 on 17's with a vertex kit.
    ...
Results 1 to 25 of 242
Page 1 of 10 1 2 3 4