Search:

If you have a press, you can push them out but if not then its a hell of a lot easier to cut the sleeve to get them out

So my original plan was to rocket bunny boss kit the car then rebuild the engine and shoot for some fairly decent power and that is what I started to do, I ordered the full kit (A rep kit from GRAMS)...

So I thought it was about I made a project thread as I've had the car 2 years now and been a member almost as long. So from the beginning...

September 2017 I sold my Turbo MK1 mx5 in order to buy...

Check clearance to the cross member, I had some some poly mounts that were evidently manufactured incorrectly and the engine sat too low and was contacting the cross member. The vibration was insane...

Yeah it works, I have been using one in mine, the only problem is that in my experience the cheapy motors that come with them tend to be really weak

These can also be sourced from the UK, A company called Torques sells them (they are in Abergavenny but sell a lot through ebay)

If I remember correctly the rack high pressure side is M14x1.5 but it is an odd fitting as it has an o-ring on it. The Return side on the rack is M16x1.5 and again is a special fitting. Unfortunately...

I moved mine to behind the dash airbag panel and made a custom fuse panel when I swapped in my RB25 and I think I only had to extend a few wires. as cooltiger said its about 6 wires at most, so i...

I was previously running ET25 17x9.5 Rota GTR-D all round with 225/40 tyres (not my choice, the previous owners) and it didn't seem to pull or tram line too much however it did rub on the arch liner...

I'm in the process of upgrading the brakes on my S14, I've got the z32 back plates and handbrake assembly for the rear and I'm just about to order the new handbrake cables so I just wanted to check;...

I found the problem in the end. The harness I had, had the cas wired incorrectly had to completely repin it

Evening, so I'm nearly done on swapping an RB25 into my S14 but I've hit a speed bump... It doesn't start.

So when cranking there is no injector pulses and no spark and the fuel pump doesn't run...

Does any one know what size the brake pedal clevis pin is? I seem to have lost it and need to order another one

It's for a 1994/1995 zenki s14

Thanks,
Hayell

Does anyone have the bolt pattern spacing for the mating surface of the Nissan 3x2 axles or got one kicking around that they could take measurements from?

I'm after the bolt spacing, hubcentric...

I'm going to doing an ABS delete on my S14 as its shot, but I just wanted to see if anyone had doen one and if so did they do it with or without a bias valve and what would you recommend?

Thanks,...

Just FYI, the Limitbreak top plates do not fit directly on HSD's as the adjustment bolts are at 58mm centres instead of 60mm however with the limitbreak pillowball and top plates they will fit.

Does anyone know if HSD Dualtech's or MonoPro's are compatible with PBM limitbreak top plates, I have the spec on the PBM top plates and after measuring the HSD top plates it seems like they will fit...

Right, as promised. Im not sure if this is right though as its occurred to me that my car may have a 3.9 diff not a 3.7 as once upon a time it was an auto and I don't know if the diff was changed.
...

I'll be pulling my cluster out tonight to pull a bulb out so I'll grab a picture then and post it for you.

Yeah I have the same issue with my s14 and re-soldering didn't work for me either. Have you confirmed that you are actually getting a tach-o signal and ruled out it being a wiring issue and not the...

So I noticed that you can get extended/adjustable rear suspension arms and I have seen ones that allow up to an additional 50mm but my question is: how does that affect the axles? surely if you...

Personally, when I did mine I pulled the engine and gearbox out. It's nowhere near as hard as it seems. You probably could do it with the block still in the car but you'll end up pulling so much of...

Yeah it doesn't look all that bad, mine had worse than that when i got it and I had it welded, I'll be welding some more over the summer as well. Just cut out the rust and weld in new steel.

Morning all,

So my S14 was originally an auto but was converted by the original owner however the muppet didn't bother wiring the reversing lights. Iv'e spent some time looking through the guides...

I finally got this sorted last night! I chucked another fuse in which blew so I ended up pulling the dash out so that I could check the harnesses and disconnect everything. Eventually I found that...