Search:

Type: Posts; User: joeshaw123

Page 1 of 15 1 2 3 4

Search: Search took 0.08 seconds.

  1. Also, my SR took plenty of abuse with 10w-40 semi...

    Also, my SR took plenty of abuse with 10w-40 semi synth from Halfords, but people recommend 15w-50 too.
  2. Definitely use a restrictor. SR's turbo oil feed...

    Definitely use a restrictor. SR's turbo oil feed is at a pressure for journal bearings. Using a ball bearing turbo you need a restrictor.

    I Think you can get them off driftworks but they're the...
  3. Replies
    7
    Views
    425

    17 or 18? I managed two 18" 255/35/18 tyres in...

    17 or 18? I managed two 18" 255/35/18 tyres in one but I dare say if they were mounted it'd have been too much of a squeeze!!
  4. Replies
    2
    Views
    334

    Not at all necessary if you aren't using the...

    Not at all necessary if you aren't using the sensors mate.
  5. Replies
    9
    Views
    703

    Depends how important the features like...

    Depends how important the features like horn/airbag light are to you.

    I used this boss: https://www.ebay.co.uk/ulk/itm/151679785873
    on my S14, removed the airbag clockspring and drilled 3...
  6. Coincidence I think, I've recently binned off my...

    Coincidence I think, I've recently binned off my slip ring thingy and everything still works as it should. Are there any fuses or earths for those things?
  7. Replies
    19
    Views
    1,657

    Yeah I was running 1.4bar on my old 2871r with...

    Yeah I was running 1.4bar on my old 2871r with stock HG and headbolts - I think a well serviced motor that hasn't been openened can take decent boost if you're not bashing it off the limiter...
  8. Replies
    19
    Views
    1,657

    Added to that I just use a simple mbc, set it...

    Added to that I just use a simple mbc, set it once and forget.
  9. Replies
    19
    Views
    1,657

    1.0 bar should be fine, but you might find if it...

    1.0 bar should be fine, but you might find if it spikes in a higher gear then you'll be close to hitting fuel cut. I was fine at 1.0-1.1 bar on my S14a but as the weather has got colder it now hits...
  10. Replies
    7
    Views
    408

    I'm almost certain that there aren't any holes on...

    I'm almost certain that there aren't any holes on a non-touring's sill panels. Which is a bit of a godsend really as they normally rot from the holes outwards on the outer sill.

    To fit the skirts...
  11. Replies
    11
    Views
    490

    R33 handbrake cables fit fine, I think it's Z32...

    R33 handbrake cables fit fine, I think it's Z32 cables that don't
  12. Adjustable. They're very similar to bride...

    Adjustable. They're very similar to bride superlow base mount rails, but fit recaro SR without any modification.

    I made my own passenger side rail, but it took a couple of evenings to do and I...
  13. And S13,14,15 rails are all very much the same...

    And S13,14,15 rails are all very much the same fitment
  14. Just FYI, Juran racing rails off nengun are a...

    Just FYI, Juran racing rails off nengun are a bolt on fit for recaro SR/speed seats. About as low mount as you can get and fit perfectly.
  15. Double post

    Double post
  16. Recaro SRs out of Evo 3/4/5 along with ek9 civic,...

    Recaro SRs out of Evo 3/4/5 along with ek9 civic, dc2 integra, celica gt4 and the like are all reclining seats with folding mechanism.

    You can just about see the little lever on the side of the...
  17. I was recommended these - seem to be working...

    I was recommended these - seem to be working fine!
    http://www.ebay.co.uk/ulk/itm/111714142025
  18. Replies
    53
    Views
    9,265

    Not done a great deal to this again; I meant to...

    Not done a great deal to this again; I meant to get the turbo slapped on over xmas but I've been a bit busy and I've not had a few days where I've not needed the car.

    Instead of making it go...
  19. Replies
    4
    Views
    341

    Wrong I'm afraid, the ABS sender is in the nose...

    Wrong I'm afraid, the ABS sender is in the nose and the rear senders are oil temperature sender and warning lamp switch. I've binned off all three.
  20. Replies
    20
    Views
    1,487

    My SR is on 238k miles (unopened) and compression...

    My SR is on 238k miles (unopened) and compression is in the 140's; I've bounced it off the limiter all day today and it takes abuse just fine.

    On the flip side my mates rebuilt forged lump, from a...
  21. Replies
    11
    Views
    924

    The missus' car that we use as the daily driver...

    The missus' car that we use as the daily driver is a *ahem*... peugeot 107...

    Infrequently we have nipped up to leeds/various west yorkshire places in it, and that wanders terribly in crosswind on...
  22. Replies
    9
    Views
    482

    I've got a japspeed elbow and one of their super...

    I've got a japspeed elbow and one of their super low twin downpipes, and it fits really nicely.
    The bracket from downpipe to gearbox was a bit off but easy to sort out.
  23. Replies
    9
    Views
    363

    Me neither. Looks like its manifold off time.

    Me neither. Looks like its manifold off time.
  24. What rear spring rates are you running? Stock...

    What rear spring rates are you running? Stock monopros come with 7kg/mm front and 5 on the rear. This is quite firm for launching, lower rates would be good - softening the dampers only does so much....
  25. Replies
    17
    Views
    1,267

    If its just the seals that have gone, and the...

    If its just the seals that have gone, and the bearings/compressor wheel/turbine wheel are all in good shape then people like owen developments can do it too, and I daresay for not huge money. Before...
Results 1 to 25 of 354
Page 1 of 15 1 2 3 4